IPM6220ACAZ-T【PDF 11/15 页】IC REG 5OUT BUCK/LDO SYNC 24SSOP

11

One of the parameters limiting the converters response to a

load transient is the time required for the inductor current to

slew to its new level. Given a sufficiently fast control loop

design, the IPM6220A will provide either 0% or 94% duty

cycle in response to a load transient. The response time is

the time interval required to slew the inductor current from an

initial current value to the load current level. During this

interval the difference between the inductor current and the

transient current level must be supplied by the output

capacitor(s). Minimizing the response time can minimize the

output capacitance required. Also, if the load transient rise

time is slower than the inductor response time, as in a hard

drive or CD drive, this reduces the requirement on the output

capacitor.

The maximum capacitor value required to provide the full,

rising step, transient load current during the response time of

the inductor is:

Where: C

OUT

is the output capacitor(s) required, L

O

is the

output inductor, I

TRAN

is the transient load current step, V

IN

is the input voltage, V

OUT

is output voltage, and V

OUT

is

the drop in output voltage allowed during the load transient.

High frequency capacitors initially supply the transient

current and slow the load rate-of-change seen by the bulk

capacitors. The bulk filter capacitor values are generally

determined by the ESR (Equivalent Series Resistance) and

voltage rating requirements as well as actual capacitance

requirements. The output voltage ripple is due to the inductor

ripple current and the ESR of the output capacitors as

defined by:

where, I

L

is calculated in the Inductor Selection section.

High frequency decoupling capacitors should be placed as

close to the power pins of the load as physically possible. Be

careful not to add inductance in the circuit board wiring that

could cancel the usefulness of these low inductance

components. Consult with the manufacturer of the load

circuitry for specific decoupling requirements.

Use only specialized low-ESR capacitors intended for

switching-regulator applications, at 300kHz, for the bulk

capacitors. In most cases, multiple electrolytic capacitors of

small case size perform better than a single large case

capacitor.

The stability requirement on the selection of the output

capacitor is that the ESR zero, f

Z

, be between 1.2kHz and

30kHz. This range is set by an internal, single compensation

zero at 6kHz. The ESR zero can be a factor of five on either

side of the internal zero and still contribute to increased

phase margin of the control loop. Therefore:

In conclusion, the output capacitors must meet three criteria: By

varying the values of the soft-start capacitors, it is possible to

provide sequencing of the main outputs at start-up.

1. They must have sufficient bulk capacitance to sustain the

output voltage during a load transient while the output

inductor current is slewing to the value of the load

transient

2. The ESR must be sufficiently low to meet the desired

output voltage ripple due to the output inductor current,

and

3. The ESR zero should be placed, in a rather large range,

to provide additional phase margin.

3.3V ALWAYS and 5V ALWAYS Output Capacitors

The output capacitors for the linear regulators insure stability

and provide dynamic load current. The 3.3V ALWAYS and

the 5V ALWAYS linear regulators should have, as a

minimum, 10礔 capacitors on their outputs.

3.3V Main and 5V Main PWM Output Inductor

Selection

The PWM converters require output inductors. The output

inductor is selected to meet the output voltage ripple

requirements. The inductor value determines the converters

ripple current and the ripple voltage is a function of the ripple

current and output capacitor(s) ESR. The ripple voltage

expression is given in the capacitor selection section and the

ripple current is approximated by the following equation:

Input Capacitor Selection

The important parameters for the bulk input capacitor(s) are

the voltage rating and the RMS current rating. For reliable

operation, select bulk input capacitors with voltage and

current ratings above the maximum input voltage and largest

RMS current required by the circuit. The capacitor voltage

rating should be at least 1.25 times greater than the

maximum input voltage and 1.5 times is a conservative

guideline.

The AC RMS input current varies with load as shown in

Figure 9. Depending on the specifics of the input power and

its impedance, most (or all) of this current is supplied by the

input capacitor(s). Figure 9 also shows the advantage of

having the PWM converters operating out of phase. If the

converters were operating in-phase, the combined RMS

current would be the algebraic sum, which is a much larger

value as shown. The combined out-of-phase current is the

square root of the sum of the square of the individual

reflected currents and is significantly less than the combined

in-phase current.

C

OUT

L

O

I

TRAN

?/DIV>

V

IN

V

OUT

(

) 2

?/DIV>

--------------------------------------------- -

I

TRAN

DV

OUT

--------------------

?/DIV>

=

V

RIPPLE

I

L

ESR

?/DIV>

=

C

OUT

1

2 ?nbsp ESR f

Z

?/DIV>

-------------------------------------------

=

I

L

V

IN

V

OUT

F

S

L

?/DIV>

------------------------------- -

V

OUT

V

IN

--------------- -

?/DIV>

=

IPM6220A

OS-CON?is a registered trademark of Sanyo Electric Company, Ltd. (Japan)

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

我的联系方式

*

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式